Development and Characterization of Recycled Polypropylene/Teak Wood Dust Composites for Sustainable Applications in the Automotive Components Industry: Thermal and Mechanical Properties

Authors

  • Erfina Oktariani Department of Polymeric Chemical Engineering, Polytechnic STMI Jakarta, Jakarta, Indonesia
  • Armilia Ailsa Ahnaf Department of Polymeric Chemical Engineering, Polytechnic STMI Jakarta, Jakarta, Indonesia
  • Rebecca Christine Department of Polymeric Chemical Engineering, Polytechnic STMI Jakarta, Jakarta, Indonesia
  • Herlin Arina Department of Polymeric Chemical Engineering, Polytechnic STMI Jakarta, Jakarta, Indonesia

DOI:

https://doi.org/10.25077/jrk.v16i2.826

Keywords:

recycled polypropylene, wood dust, composite, mechanical properties, crystallinity

Abstract

Utilizing recycled plastics is a crucial strategy for reducing waste and developing sustainable materials. Most of the recycled polypropylene (PP) in the industry is from reprocessed scrap. In contrast, this study explores a more challenging feedstock: post-consumer water cups collected by waste pickers, representing an environmentally impactful pathway. The recycled PP was combined with teak wood dust, an abundant lignocellulosic byproduct, antioxidant additives (Irganox 1010, Irgafos 168), and polypropylene-grafted-maleic anhydride (PPgMA) as a coupling agent to produce composites for the potential automotive component industry. Teak wood dust was added at 0–20 wt% to evaluate its influence on the thermal and mechanical performances. Fourier-transform infrared (FTIR) analysis confirmed that recycled PP maintained the functional groups similar to virgin PP, supporting its recyclability. Differential scanning calorimetry (DSC) showed decreasing enthalpy of fusion (101 to 91 J/g) and crystallinity (48% to 44%), indicating the disruption of crystalline packing by teak wood dust filler. The composites exhibited improved flexural strength and modulus with increasing filler content, attaining maximum values of 56.2 MPa and 2,132.9 MPa at 20 wt%. However, Izod impact strength decreased from 564 J/m (0 wt%) to ~300 J/m (20 wt%), indicating a trade-off between stiffness and toughness. Despite this reduction, all composites exceeded the minimum Izod impact strength requirement for automotive polypropylene copolymers (≥75 J/m, SNI 8432:2022). Overall, this study highlights the feasibility of valorizing both post-consumer plastic waste and wood dust into functional, sustainable composites for automotive components.

References

1. D. Jubinville, C. Tzoganakis, and T. H. Mekonnen, “Simulated Recycling of Polypropylene and Maleated Polypropylene for the Fabrication of Highly-Filled Wood Plastic Composites,” ACS Appl Polym Mater, vol. 4, no. 4, pp. 2373–2383, Apr. (2022), doi: 10.1021/acsapm.1c01671.

2. F. Chen and M. Zhang, “Maleic anhydride-modified polyolefins as compatibilizer for lignin-reinforced polypropylene composites,” Polym Compos, vol. 40, no. 7, pp. 2594–2601, Jul. (2019), doi: 10.1002/pc.25053.

3. A. K. Bledzki, M. Letman, A. Viksne, and L. Rence, “A comparison of compounding processes and wood type for wood fibre - PP composites,” Compos Part A Appl Sci Manuf, vol. 36, no. 6, pp. 789–797, Jun. (2005), doi: 10.1016/j.compositesa.2004.10.029.

4. K. Marsh and B. Bugusu, “Food packaging - Roles, materials, and environmental issues: Scientific status summary,” Apr. (2007). Doi: 10.1111/j.1750-3841.2007.00301.x.

5. V. Siracusa, P. Rocculi, S. Romani, and M. D. Rosa, “Biodegradable polymers for food packaging: a review,” Trends Food Sci Technol, vol. 19, no. 12, pp. 634–643, (2008), doi: https://doi.org/10.1016/j.tifs.2008.07.003.

6. S. M. Al-Salem, P. Lettieri, and J. Baeyens, “Recycling and recovery routes of plastic solid waste (PSW): A review,” Waste Management, vol. 29, no. 10, pp. 2625–2643, (2009), doi: https://doi.org/10.1016/j.wasman.2009.06.004.

7. J.-Marc. Roda, Atlas of wooden furniture industry in Jepara, Indonesia. Published by French Agricultural Research Centre for International Development ; Center for International Forestry Research, (2007).

8. H. Krisnawati, E. Varis, M. Kallio, and M. Kanninen, “Paraserianthes falcataria (L.) Nielsen : Ecology, silviculture and productivity.”

9. N. Nugroho and N. Ando, “Development of structural composite products made from bamboo II: fundamental properties of laminated bamboo lumber,” Journal of Wood Science, vol. 47, no. 3, pp. 237–242, (2001), doi: 10.1007/BF01171228.

10. G. Lukmandaru et al., “Chemical Properties of ‘Jati Unggul Nusantara’ Teak Wood from Gunungkidul,” (2024).

11. K.-N. Law, W. Rosli, W. Daud, and A. Ghazali, “Morphological and chemical nature of fiber strands of oil palm empty-fruit-bunch (OPEFB).”

12. K. L. Chin, P. S. H’ng, L. J. Wong, B. T. Tey, and M. T. Paridah, “Optimization study of ethanolic fermentation from oil palm trunk, rubberwood and mixed hardwood hydrolysates using Saccharomyces cerevisiae,” Bioresour Technol, vol. 101, no. 9, pp. 3287–3291, (2010), doi: https://doi.org/10.1016/j.biortech.2009.12.036.

13. K. K. Aloma, Sudirman, E. Hertinvyana, Sudaryanto, G, and Indra, “Pengaruh anti oksidan terhadap degradasi plastik polipropilen,” (2005).

14. E. Oktariani, H. Arina, and R. Christine, “Penyuluhan pemanfaatan limbah serbuk kayu sebagai penguat polipropilena di pt. Laksana tekhnik makmur,” Aptekmas, vol. 6, no. 1, (2023), doi: 10.36257/apts.vxix.

15. A. Kumar Yadav and R. Srivastava, “Selection of teak sawdust polypropylene composite’s composition for outdoor applications using TOPSIS analysis,” Sādhanā, vol. 45, no. 231, pp. 230–242, (2020), doi: 10.1007/s12046-020-01435-wS.

16. R. D. Zulnazri, “41-60-1-SM,” Jurnal Teknologi Kimia Unimal, vol. 1, no. 1, pp. 65–78, 2012.

17. M. Poletto, “Natural oils as coupling agents in recycled polypropylene wood flour composites: Mechanical, thermal and morphological properties,” Polymers and Polymer Composites, vol. 28, no. 7, pp. 443–450, Sep. (2020), doi: 10.1177/0967391119886941.

18. B. Cihad Bal, “Mechanical properties of wood-plastic composites produced with recycled polyethylene, used Tetra Pak® boxes, and wood flour” Bioresources, vol. 17, no. 4, pp. 6569–6577, (2022), doi: 10.15376/biores.17.4.6569-6577.

19. C. Homkhiew, T. Ratanawilai, and W. Thongruang, “Effect of wood flour content and cooling rate on properties of rubberwood flour/recycled polypropylene composites,” in Advanced Materials Research, (2012), pp. 495–500. doi: 10.4028/www.scientific.net/AMR.488-489.495.

20. K. Alokabel and A. Deka Betan, “Pengaruh Variasi Serbuk Kayu terhadap Sifat Mekanis Material Komposit,” (2019).

21. E. Mchenry and Z. H. Stachurski, “Composite materials based on wood and nylon fibre,” (2003). [Online]. Available: www.elsevier.com/locate/compositesa.

Downloads

Published

2025-09-30

How to Cite

Oktariani, E., Ahnaf, A. A., Christine, R., & Arina, H. (2025). Development and Characterization of Recycled Polypropylene/Teak Wood Dust Composites for Sustainable Applications in the Automotive Components Industry: Thermal and Mechanical Properties. Jurnal Riset Kimia, 16(2), 97–107. https://doi.org/10.25077/jrk.v16i2.826

Issue

Vol. 16 No. 2 (2025): September

Section

Articles

Citation Check

License

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Please find the rights and licenses in Jurnal Riset Kimia (J. Ris. Kim). By submitting the article/manuscript of the article, the author(s) agree with this policy. No specific document sign-off is required.

1. License

The use the article will be governed by the Creative Commons Attribution license as currently displayed on Creative Commons Attribution 4.0 International License. 

2. Author(s)' Warranties

The author warrants that the article is original, written by stated author(s), has not been published before, contains no unlawful statements, does not infringe the rights of others, is subject to copyright that is vested exclusively in the author and free of any third party rights, and that any necessary written permissions to quote from other sources have been obtained by the author(s).

3. User Rights

Under the Creative Commons license, the journal permits users to copy, distribute, and display the material for any purpose. Users will also need to attribute authors and J. Ris. Kim on distributing works in the journal and other media of publications.

4. Rights of Authors

Authors retain all their rights to the published works, such as (but not limited to) the following rights;

  • Copyright and other proprietary rights relating to the article, such as patent rights,
  • The right to use the substance of the article in own future works, including lectures and books,
  • The right to reproduce the article for own purposes,
  • The right to self-archive the article,
  • The right to enter into separate, additional contractual arrangements for the non-exclusive distribution of the article's published version (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.

5. Co-Authorship

If the article was jointly prepared by more than one author, any authors submitting the manuscript warrants that he/she has been authorized by all co-authors to be agreed on this copyright and license notice (agreement) on their behalf, and agrees to inform his/her co-authors of the terms of this policy. J. Ris. Kim will not be held liable for anything that may arise due to the author(s) internal dispute. J. Ris. Kim will only communicate with the corresponding author.

Similar Articles

1 2 3 4 5 6 7 8 9 > >> 

You may also start an advanced similarity search for this article.